Click on the image to view the original image
Programmable rgb SD card Pixel led controller LPD6803 WS2811 Strip Module 2048 Pixel SD Card T1000s Full Color LED Controller
T-1000S System features
1, 32—256 Gray level,Support software Gamma correction.
2,Support the rules and special-shaped handle.
3,Single-port output,can support 2048 pixels.
4,Off-line(SD Card) control, play back content stored in the SD card.
5,T-1000S store a maximum of 16 programs,copy multiple files to the SD card in order,after formatting the SD card as “FAT” format.
6,The program must be named in orders . just as :00_1.led, 01_1.led, 02_1.led.
7,Compatible with single line or double line chips
Description:
Memory card:
A. . When T-1000S controller control less than 512 lamps the frame rate can reach 30fps. When T-1000 S controls more than 512 lamps and less than 1024 lamps the frame rate will slow down automatically.
B. In the 2012 production version of the T-1000 to add a Chinese flag on the surface, you must use the new software.
C. Before copy files to SD card ,The SD card must be formatted as FAT format.
IC supported | Software code& Controller type | Pixel /(MAX) | NOTE |
| LPD6803, D705,1101, 6909, 6912 | T-1000s-6803 | 2048 | |
| LPD8806, LPD8809 | T-1000s-8806 | 2048 | |
| TM1803, TM1804, TM1809, TM1812 | T-1000s-TM | 2048 | TM1804&TM1809 Divided into high speed and low speed |
| TM1903, TM1904, TM1909, TM1912 | T-1000s-TM19 | 2048 | |
| UCS6909, UCS6912, UCS7009, UCS5903 | T-1000s-UCS32 | 2048 | |
| UCS1903, UCS1909, UCS1912 | T-1000s-UCS256 | 2048 | Divided into high speed and low speed |
| UCS3903 | T-1000s-UCS1024 | 2048 | |
| DMX512 | T-1000s-DMX | 170/512 | Compatible with standard DMX512 |
| WS2801, WS2803 | T-1000s-WS | 2048 | |
| WS2811 | T-1000s-WS2811 | 2048 | Divided into high speed and low speed |
| DS189 | T-1000s-DS189 | 2048 | |
| TLS3001, TLS3002, TLS3008 | T-1000s-TLS | ||
| P9813 | T-1000s-P9813 | 2048 | |
| SM16715 | T-1000s-SM16715 | 2048 | Divided into high speed and low speed |
| SM16716 | T-1000s-SM16716 | 2048 | |
| BS0901, BS0902 | T-1000s-0901 | 2048 | |
| BS0815 | T-1000s-0815 | 2048 |
3. The meaning of flag :
| Button | Meaning | |
| SET | Save your adjust | |
| MODE | Switch effect file | |
| SPEED+ | Turn up speed | Press speed+ and speed- at the same time the program will play circularly. |
| SPEED- | Turn down | |
| DC 5V | +5V power input |
| GND | Power GND input |
| 7.5-24V | +7.5-24V power input |
| POWER | Power indicator |
| ERROR | Error indicator |
| SD CARD | SD card slot |
TTL signal(245/spi signal): RS485 signal.
| CLK | Clock signal | B | Signal A / DMX+ |
| DAT | Data signal | A | Signal B / DMX- |
| GND | Signal ground | GND | Signal ground |
NOTE:
For the TTL(SPI) signal, the controller signal ground must connect to the LED ground wire directly.
Mode of connection
1. Multiple T-1000S controllers can be cascaded together and work synchronously.
2. T-1000S one TTL(SPI) signal and one RS485 signal port output,can control 2048 pixels/lamps;
3. When the chip for LED is single line chip just with data, then just need to be connected with DAT and GND of the controller. If the chip for LED is double line chip with DAT and CLK, then need to be connected with DAT, CLK, and GND of the controller.
4. If you need to use RS485 signal you need to connect controller A interface with LED lamps A (DMX+), controller B interface with LED lamps B(DMX-),
5. If you need to control a new IC type by the controller, software code mode is:T-1000-IC model.
Question 1:After power,the T-1000S ERROR indicator has been flashing without display output
answer:The ERROR indicator has been flashing means the controller did not read the card correctly, possible problems:
1. SD card is empty, with no effect file.
2.The effect file in the SD card and the controller model are not match, please choose correct controller model in LedEdit and then re-create the effect file *led.
3.SD card did not format to FAT before copy effect files.
4. Please check the supply power voltage, the controller can be individually powered to exclude power reasons
5Changing the SD card and then test to exclude the possibility of a bad SD card
Question 2: The controller is powered on, the indicator is normal, but the lamps have no effect change
Answer: The reasons for this are as follows:
1 Check if the lamp′s signal line and the controller connected correctly
2 If the TTL signal is received, the lamp and the controller must be common ground, that means connect the lamp′s and the controller′s ground wire together
3 Check if the model chose during making display files on the SD card match the chips used in the lighting
Question 3:Controller and light connected, after. Lamps flicker. Controller indicator to normal.
Answer:
1 The ground wire is not connected between the controller and lighting.
2 The file in SD card is bad, Chip model does not match with the actual.
3 Insufficient power supply.
Question4: The SD card can not be formatted.
Answer:
1 First make sure the SD card on the side of the protection switch is already open.
2 SD card reader is broken
3 Do all of this can’t deal with the question. Change the SD card tests again.
More question about controller , please contact me no hesitate .
