Click on the image to view the original image
- Using Range of Rotating Beacon
This handbook describes apron rotation beacons manufactured to FAA AC 150 / 5345-12 and ICAO Annex 14 and Airport Design Manual. Pleasestrictly follow the FAA and ICAO and other relevant provisions of the norms of the use of the lamp.
- Technical Characteristics
| Interval | Parameter | Action |
| Every day | Lamp failure | Change Lamp |
| Light output is low | 1.If the glass surface is dirty, wipeit clean 2.Check lamp deviation or moisture 3.Check lamp aging or shifting | |
| Every Week | Light output channel obstructions | Clean the path and prism surface |
| Every Month | The presence of moisture and water(Visual inspection of prism inner surface) | 1. Turn on the lamp body 2. Clean, dry and check 3. Replace O-rings and other damaged parts |
| Every Two Month | Tighten the screw | Check the lamp body tightness bolts are locked |
| After 1200 hours 6.6A operation | Change Lamp Bulbs | Recommended When the service life is reached, replace the lamp systematically. At rated power (6.6A), up to 1200 hours. But in actual operation, the lamp life may reach 2000 to 4000 hours |
It is recommended to increase the number of maintenance during the rainy season to
ensure the normal operation of the lamp
It is suggested that the system replace the lamp when the lamp reaches the service life
(80% light intensity)
- Specification
- Light intensity, light color meet the requirements.
- Sophisticated optical control, light utilization, high brightness, outstanding optical
performance. - Lamps shape is handsome, good thermal performance, well-designed.
- The lamp uses a split structure, reducing impurities and moisture into the lamp,
improving the service life of lamp optics, reducing the number of maintenance operations. - The main body of the lamp is made of aluminum alloy, the fastener is made of stainless
steel, and the anti-corrosion performance is good. - Adopts high-precision machine tool processing, ensuring a full range of lamps quality and
accuracy.
- Adjust the Angle of the Lamp
Check the lamp pointer engraved clearly visible, loosen the side of the set screw, adjust the lamp elevation angle through the front and rear angle adjustment screw until the pointer points to a predetermined angle value, locking the set screw.
- Lamp Maintenance
The routine maintenance recommendations provided in this section are for informational purposes only. The airport may establish its own routine maintenance guidelines based on other regulations or the maintenance experience of the airport staff themselves.
Airport lighting maintenance, please refer to "1.0 Foreword" described, by professionals.
- Change Bulbs
Turn off the power, open the lamp cover, unplug the lamp pin. Holding the thumb and forefinger on the tail of the bulb, rotate the bulb to align the circular notch in the lower part of the lamp tray with the clip of the lamp holder and remove the bulb backward. Thumb and forefinger holding the tail of the bulb, the lower circular notch of the lamp tray alignment a snap bracket , rotate the bulb 90 degrees, so that the lamp bracket buckle stuck lamp panel, the lamp pin into the holder.
can be.
1. Never replace the lamp from the front of the lamp; remove the lamp.
2. The working position of the bulb is the direction of the notch of the .
| Application Environment | Technical Indicators |
| Altitude below 2500 meters; Outdoor: -40 ℃ - +55 ℃; Relative humidity: 95%; (+ 24.5 ℃), the maximum humidity can be greater than 100% ; Rain, snow, ice, water; Corrosive salt spray. | Halogen lamp3*150W; Lamp Using Life: ≥1000 hours; White,Green,Yellow Color; Lamp angle can be adjusted; 12 RPM, 36 times per minute flash; 304 Steel cabinet with powder layer; Voltage:AC220V. |
- Installlation Way
- If installed on a flat surface (such as concrete floor), the bafflewith expansion screws on the concrete floor.
- If installed in uneven ground (such as land) in this case,you need to be fixed in the concrete block.
- Installation Steps
- When open the package, check that the parts are complete and handle lamps carefully to avoid damage.
- Fix the lamp through the bottom plate screw and open the cover to connect the cable
Product Pictures Structure 
| 1.Synchronized Flashing Units Can"t work Simultaneously |
| A. Monitor Function Type Requires Power Line seperate from signal line,the power circuit of each unit can be independently connected,pls check signal circuit was connected by corresponding color when ensure power supply works normally. |
| B. Check if there"s short circuit or leakage phenomenon with the signal circuit after excluding the condition above. |
| 2.Light-operated switch can"t work normally |
| A.The Unit can"t work at day: Pls check if the light-operated detector is closed over by dust; |
| B. The Unit can"t work at night: Pls check if light-operated detector is influenced by direct light or strong reflective light; |
| C. esting the unit at day: Most of customers test the unit by Closing over the light-operated detector using their hands.Since the strong Radiation of sunshine,the light-operated function can"t work.The proper method is using 3 layers of black opacity adhesive tapes. |
| 3.Are you the Manufactory or Trading? |
| Our company is professional Manufactory to produce the Aviation Obstruction light. |
| 4.What Kind of Package you choose? |
| As usual,we use the Carton Box; If delivery by sea,we will use the Wooden case to pack. |
| 5.What’s your warranty? |
| Full Warranty:2-5 Years. |
| 6.Do you accept OEM/ODM service? |
| Yes.We can supply you OEM/ODM service to you. Cause we are the manufacturer. There is professional R&D team in our company. |
| Contact Person: Jodie Shaw Whatsapp:+86 15907360172 Wechat:008615907360172 Skype ID: ucanter-parts Phone:86-15907360172 Tel:+86-0731-85563265 Fax:+86-0731-85563365 Website:https://www.cdt-en.com https://www.chendongtech.com | |