- Type:
- Aviation Obstruction Lights
- Input Voltage(V):
- AC110V 220V
- Lamp Power(W):
- 105
- Lamp Luminous Flux(lm):
- 0
- Lamp Luminous Efficiency(lm/w):
- 0
- CRI (Ra):
- 0
- Color Temperature(CCT):
- White
- Beam Angle(°):
- 15
- IP Rating:
- IP65
- Certification:
- BV, CE, EMC, RoHS, SASO
- Emitting Color:
- White
- Lamp Body Material:
- Stainless Steel
- Base Type:
- Others
- Light Source:
- Halogen Bulbs
- Place of Origin:
- Hunan, China
- Brand Name:
- CDT
- Light source:
- pre-focused halogen reflector lamp
- Power Supply:
- AC110V,AC220-230V,50-60Hz
- Electrical consumption:
- Less than 250 W for the SAGA system
- Visual range:
- 10 nautical miles in standard visibility conditions
- Operation angular sector:
- 15 degrees on both side of the approach axis
- Axis accuracy:
- +/- 0.45 degree in azimuth
- Delay between flashes:
- From 60 to 300 ms
- "Flashes" frequency:
- 0.5 Hz
- Body material and paint:
- Body, Cap and Support are in aluminium alloy, painted aviation yellow
- Remote CMS:
- Remote control from 48 Vdc
- Supply Ability:
- 100 Set/Sets per Month
- Packaging Details
- paper carton&wooden carton
- Port
- Shanghai,Guangzhou ,Shenzhen
- Lead Time:
Quantity(Units) 1 - 50 >50 Est. Time(days) 7 To be negotiated
Setting Information for new heliport SAGA system Product | |
Lamp | One 12 Vac 105 W pre-focused halogen reflector lamp |
Power supply | 110 Vac or 220-230 Vac 50/60 Hz |
Electrical consumption | Less than 250 W for the SAGA system and 240 W maximum for the heating resistors |
Visual range | 10 nautical miles in standard visibility conditions |
Operation angular sector | 15 degrees on both side of the approach axis |
Axis accuracy | +/- 0.45 degree in azimuth |
Delay between flashes | From 60 to 300 ms |
“Flashes” frequency | 0.5 Hz |
Finish | Body, Cap and Support are in aluminium alloy,phosphated and painted in aviation yellow. All fixings and fastenings are stainless steel. The IP 65 – 20Joules Power Supply Box is made of reinforced polyester |
Working temperature | From -40°C to +50°C |
Remote CMS | Remote control from 48 Vdc. Monitoring feed back signal using two dry contacts (Contact capacity = 250 V / 1A maximum). |
Product Details
The SAGA system includes two light units (one Master and one Slave) placed symmetrically on both sides of the Runway (or TLOF) threshold supplying unidirectional rotating beams which give a flashing effect.The pilot receives, each second illumination of two “Flashes” provided in sequence bythe two light units.
• When the aircraft flies inside a 9° width angular sector, centred on the approachaxis, the pilot sees the two lights “flashing” simultaneously.
• When the aircraft flies inside a 30° width angular sector, centred on the approach axis and outside the previous one, the pilot sees the two lights “flashing” with a variable delay (60 to 330 ms) according to the position of the aircraft in the sector.
The further the aircraft is from the axis, the greater the delay. The delay between the two “flashes” produces a sequence effect which shows the direction of the axis.
• The visual signal is not visible when the aircraft flies outside the 30° angular sector.
Location of the field
1.The two light units of a SAGA system must be installed at 10 metres from the runway.
2.Edge symmetrically on both sides of the Runway threshold (for TLOF the two units must be installed as close as possible to the threshold edges).
3.The Master unit must be installed on the right of the Threshold and the Slave unit on the left.
Design
1. SAGA optical head
2. SAGA power supply box
3. Frangible leg
4. Power supply box
fixation bars (x 2)
5. Power supply box fixing
screws (x 4)
6. Clamps for leg fixation
(x2) with nuts and
washers (2 sets by
clamp)
7. M18 –400mm Sealing
rods (x 4) with nuts and
washers for fixation of
the leg (supplied with
the leg)
Main Advantages.
• Safe operation: The SAGA system is automatically stopped when at least one of its light units is out of service. A signal is available for monitoring of this default status in the control room.
• Easy maintenance: Very easy access to the lamp and all terminals. No special tools are required.
• Brilliancy levels: The remote control of three brilliancy levels is possible for a better visual comfort for the pilot (no dazzling).
• Efficiency: Coupled with a PAPI, the SAGA system supplies the pilot with the security and the comfort of an Optical “ILS”.
• Climate: In order to maintain operation even in very cold and/or wet areas, the light units of SAGA are equipped with heating resistors.
• Additions of red filters (option) provide to the SAGA system with the option of emitting red Flashes corresponding to fly exclusion zone due to obstacles.
Mecanical Installation
Mechanical fixing of the SAGA light unit can be done in two ways:
1. On a hard surface (such as a concrete platform) using four sealing rods sealed in the concrete.The four sealing rods must be installed in square(sides = 200 mm).
2. On a surface which is not hard (such as earth) by using the four sealing rods delivered with the system. In this case, fixing is made on a concrete block (recommended standard sizes400 x 400 x 700 mm). The rods (M18 –400mm) must be sealed in the block making a 200 mm side square (the holes in the base plate have diameters of 22 mm).
Note: Adjustment of the optical head azimuth angle and to the horizontal is made using an aiming tool. The two SAGA units are delivered assembled and wired (connections power supply box / optical head).
Dimensions
Total height: 835 mm.
Optical head height: 335 mm, diameter = 254 mm.
Power supply box: 400 x 300x 160 mm.
Frangible leg height: 500 mm, base plate = 250 x 250 mm.
Electrical Cabling.
The SAGA System is comprised of two light units, one Master (A) and one Slave (B) linked together by electrical wiring. The figure below shows all the electrical connections of a complete SAGA system, connections between lights units + connection with the main supply distribution panel (C)+ connection with control and monitoring desk (D) + connection between power supply box (E) and optical head (F).(Reference the following picture)
Q1. Can I have a sample order for led light?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.
Q2. What about the lead time?
A:Sample needs 6-9 days, mass production time needs 1-2 weeks for order quantity more than
Q3. Do you have any MOQ limit for led light order?
A: Low MOQ, 1pc for sample checking is available
Q4. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping also optional.
Q5. How to proceed an order for aircraft warning light?
A: Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our suggestions.
Thirdly customer confirms the samples and places deposit for formal order.
Fourthly We arrange the production.
Q6. Is it OK to print my logo on aviation obstruction light product?
A: Yes. Please inform us formally before our production and confirm the design firstly based on our sample.
Q7: Do you offer guarantee for the products?
A: Yes, we offer 3 years warranty to our products.
Q8: How to deal with the faulty?
A: Firstly, Our products are produced in strict quality control system and the defective rate will be less
than 0.2%.
Secondly, during the guarantee period, we will send new lights with new order for small quantity. For
defective batch products, we will repair them and resend them to you or we can discuss the solution i
ncluding re-call according to real situation.