Click on the image to view the original image
- Place of Origin:
- CHINA
- Brand Name:
- SUNWIND
- Model Number:
- M860L
- Motor Type:
- Stepper Motor
- STEPPER MOTOR DRIVER:
- STEPPING MOTOR DRIVERS
- Supply Ability:
- 100000 Set/Sets per Week
- Packaging Details
- PAPER CARTON SUITABLE FOR THE AIR/SEA/LAND TRANSPORTATIONS.
- Port
- SHENZHEN
- Lead Time:
Quantity(Sets) 1 - 1000 >1000 Est. Time(days) 15 To be negotiated
M860L Stepper Motor Driver,DC18-50V/2.6-7.2A arduinoo stepper motor driver
stepper motor driver,servo driver,driver integrated servo motor,automation products,setpper motor controller,3-axis stepper motor controller
Product Abstract:
The M860 is a great performance microstepping based on pure-sine current control.With those technologies and the self-adjustment function(self-adjust current control) to various motors, the stepper driver keep the driven motors run with low noise,less heating, smoother movement and better performances at higher speed than other drives in the markets.it is adapt to driving 2,3,4 phases hybrid stepper motors.The M860L Stepper Motor Drivers is a excellent performance microstepping based on pure-sine current control.With above technology and the self-adjustment function(self-adjust current control) to various motors, keep the driven motors run with low noise,less heating, smoother movement and better performances at higher speed than other drives in the markets.it is adapt to driving 2,3,4 phases hybrid stepper motors.
M860L Stepper Motor Driver Features
High Efficiency
Excellent high speed performance
DC18-50V
2.6-7.2A
Self-adjustment function
Pure-sine current control
300KHz Max Pulse input frequence
Suitable for TTL and optically isolated input
Auto idle current reduction
16 steps resolutions in decimal binary, max 51,200 steps/rev
Suitable for 2 ,3, 4 phases motors
Support PUL/DIR and CW/CCW modes
Short-voltage protection, over-voltage protection, over-current protection
M860L Stepper Motor Driver Specifications
M860L Stepper Motor Driver Electrical Specifications (Tj : 25oC~77oC)
Parameters | M860L | |||
Min | Typical | Max | Unit | |
Output Current | 1.80 | - | 7.2 (5.1 RMS) | A |
Input Voltage | +24 | +68 | +80 | VDC |
Logic Signal Current | 7.00 | 10 | 16 | Ma |
Pulse input frequency | 0.00 | - | 300 | KHz |
PulseWidth | 2.50 | - | - | Us |
Pulse Voltage | 5.00 | - | 24 | VDC |
Isolation resistance | 500.00 |
|
| MΩ |
M860L Stepper Motor Driver’sConnector P1 Configurations
| Pin Function | Details |
| PUL+(+5V) | Pulse signal: In single pulse pulse/direction) mode, this input represents pulse signal, effective for each rising or falling edge (set by inside jumpers in JP1); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,effective for high level or low level (set by inside jumpers in JP1). For reliable response, pulse width should be longer than 1.5μs. Series connect resistors for current-limiting when +12V or +24V used. |
| PUL-(PUL) | |
| DIR+(+5V) | DIR signal: In single-pulse mode, this signal has low/high voltage levels,representing two directions of motor rotation; in double-pulse mode (set by inside jumper J3), this signal is counter-clock (CCW) pulse,effective for high level or low level (set by inside jumper J1). For reliable motion response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH,0-0.5V when DIR-LOW. |
| DIR-(DIR) | |
| ENA+(+5V) | Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary,namely Low level for enabling.) for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED). |
| ENA-(ENA) |
M860L Stepper Motor Driver’sConnector P2 Configurations
| Pin Function | Details |
| GND | DC/AC power ground |
| +V | DC/AC power supply, 20~80V, Including voltage fluctuation and EMF voltage. |
| A+,A- | Motor Phase A |
| B+,B- | Motor Phase B |
M860L Stepper Motor Driver’s Microstep and Current
The drives uses an 8 bits DIP switch to set stepper motor resolution and motor operating current, as shown below:
Dynamic Current(1/2/3) Microstep Resolution(6/7/8)
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
Standstill Current(4,Half/Full)
M860 Stepper Motor Driver’sMicrostep Resolution Selection
Microstep resolution is set by SW5, SW6, SW7, SW8 of the DIP switch as show in following:
| Step Angle | Pulse/Rev | SW5 | SW6 | SW7 | SW8 |
| 0.9 | 400 | ON | ON | ON | ON |
| 0.45 | 800 | ON | OFF | ON | ON |
| 0.225 | 1600 | ON | ON | OFF | ON |
| 0.1125 | 3200 | ON | OFF | OFF | ON |
| 0.05625 | 6400 | ON | ON | ON | OFF |
| 0.028125 | 12800 | ON | OFF | ON | OFF |
| 0.014063 | 25600 | ON | ON | OFF | OFF |
| 0.007031 | 51200 | ON | OFF | OFF | OFF |
| 0.36 | 1000 | OFF | ON | ON | ON |
| 0.18 | 2000 | OFF | OFF | ON | ON |
| 0.072 | 5000 | OFF | ON | OFF | ON |
| 0.036 | 10000 | OFF | OFF | OFF | ON |
| 0.0144 | 25000 | OFF | ON | ON | OFF |
| 0.0072 | 50000 | OFF | OFF | ON | OFF |
M860L Stepper Motor Driver’sCurrent Settings
The first three bits (SW1, SW2, SW3) of the DIP switch are used to set the dynamic current. Select a setting that closest to your motor"s required current.
| Peak current (A) | RMS(A) | SW1 | SW2 | SW3 |
| 2.40 | 1.71 | on | on | on |
| 3.08 | 2.20 | off | on | on |
| 3.77 | 2.69 | on | off | on |
| 4.45 | 3.18 | off | off | on |
| 5.14 | 3.67 | on | on | off |
| 5.83 | 4.16 | off | on | off |
| 6.52 | 4.66 | on | off | off |
| 7.20 | 5.14 | off | off | off |
Note:Due to motor inductance, the actual current in the coil may be smaller than the dynamic current setting, particularly in high speed condition.
M860L Stepper Motor Driver’s Typical Connections