Share
Brand： |
none |
Address： |
China |
Min.Order： |
none |
Supply： |
none |
Valid until： |
Long Term |
Type： |
Array |
Product Details
Low Voltage Emergency Packs
Matched program :Ni-CD/Ni-MH/Li-ion Battery Pack + Inverter
Input: 85-265V 50/60Hz
Output : Constant current output
Lamp : LED Light With External Driver
Charge Time:24 hours
Discharge Time : 1-3 Hours
Battery Ah : 2.0Ah-8.0Ah
Note: do not connect the battery opposite direction.
EME Range for led lights with external driver
Input Voltage: 85-265V AC 50/60Hz
Em.Power Watts:Max 25W
EM.Duration: 3 Hours
Em.Ouput current: Constant current output
Em.Output Voltage:10-60V DC
Battery type: High Temperature ni-cd cells
Recharge time: 24 hours
Amblent Temp:0℃-55℃
Technical Details
Em.Power Watts : 5W-25W
Em.Duration : 3 Hours
Battery Voltage:6V-12V series
Battery Capacity Ah : 3Ah-8Ah
Charge Current :150mA-400mA
Cut-off Voltage: 5V-10V
EMI Range For LED Light With Internal Driver
110-220V AC high voltage emergency lighting conversion kits.Designed specifically to suit internal driver’s light, such as LED tube,led bulb
Specification
Input Voltage: 85-265V AC 50/60Hz
Em.Power Watts:Max 50W
EM.Duration: 3 Hours
Em.Ouput current: 110-220V AC
Battery type: High Temperature ni-cd cells
Recharge time: 24 hours
Amblent Temp:0℃-55℃
Technical Details
Em.Power Watts : 10W-50W
Em.Duration : 1-3 Hours
Battery Voltage:12V series
Battery Capacity Ah : 3Ah-10Ah
Charge Current :150mA-500mA
Cut-off Voltage: 10V
EMI Range Wiring Diagram
EMF Range For Fluorescent Lamp
EMF Range Emergency Pack is widely used for all of fluorescent lamps including T5/T8/PL/CFL/2D and so on.
The emergency inverter provide high power and high voltageto the lamp directly without assorting with ballast or starter in case of mains off, Emergency power can be set up 4W to 8W while emergency duration can be customized freely
•IC controlled Dual rate Charger for energy savings.
•Short circuit protection at battery terminals.
•Battery reverse protection functionality
•Suit 8 - 80W fluorescent lamps
•Premium 70°C high temperature Nickel Cadmium batteries
•LED charging state indicator
•Test button to stimulate mains power failure
•Suitable for use with electronic or magnetic ballast
•Comply with European standards EN 61 347-2-7 and offer a high level of quality and safety meeting the various prevailing regulations.
Specification
Inner package material : Retardant White Plastic
Charging power: AC110V-AC265V， 50HZ/60HZ
Emergency time: 1-3 hrs
Emergency conversion time : Less than 0.1Sec
Charging time : 24h
Emergency output current : Around 1200mA(battery)
Battery Capacity:1Ah-10Ah
Emergency output voltage : 1000V
EMF Range Wiring Diagram
Non-maintained fitting
Non-maintained fitting – is normally switched off, with its batteries being continuously charged and a green LED showing fully charged. When the power fails then the fitting switches on using its battery supply. Non-maintained fittings are not part of the general lighting but are fittings such as emergency exit signs.
Maintained fitting
Maintained fitting – will operate as a normal light fitting and be controlled with all the other lights in the area, however when the power fails the maintained emergency fitting will continue to operate but, at a lower light level.
Customer Reviews total 0 items