2.4G RF wireless sync MINI led controller RGB 12-24V, 3CH*2A 

HX-MINI001-RGB(Only receiver)

MINI series wireless-sync-control led controller for RGB

Controller adopts the most advanced PWM (Pulse Width Modulation) digital control technology, it is used for controlling constant voltage LED lamps. For instance, point source of light, flexible light strip, led modules, led strings and so on; 

Product Features

l Designed for RGB constant voltage LED lights.

l DC12-24V, output current: 3chs*2A(RGB)

l Adopts RF remote control, no need line-of-sight. 4 zones separately control or all-control.

l Wireless-sync-control in both static color and dynamic modes, unlimited by remote control distance.

l Batch-operation is available for RF code matching/clearing between remote control and receivers.

l Memory function, each time power-on reserve the mode which stop in the last power-off.

l Perfect control effect, including 1024 static colors and soft dim function.

l The brightness of static color is adjustable, 1024 levels in total; the speed of dynamic changes is adjustable, 100 levels in total.

l Long-press the brightness and speed key can get the fast adjustment, convenient for operation.

l Also adopts Button function for switch on/off and change color.

l Warranty of this product is three years, exclude the artificial situation of damaged or overload working.

Technical Parameters

Controller

Remote control

Dimensions

Direction for use

 Wireless-synchronization function

Receivers will transmit the control signals from the remote control and self-inspection the work statues for each other, so multiple receivers in same zone will wireless-sync-work completely, not only static mode but also dynamic mode, to achieve wired-like operation experience.

Button control function

1. Short pressing to switch on/off the light in any time.

2. Long-pressing during the controller in working state, the output light brightness / color will change to any available state in cycle, just release press when you get the correct brightness/color.

3. long-pressing during the controller in off state for 5 seconds will enter “color-order-setting” state, followed by short-pressing will change the color-order from GRB-BRG-RGB in turn, LED load will flash as “ red-green-blue-off” when the color-order of controller is as same as with led load; followed by 2 sends long-pressing will save the color order and exit the “color-order-setting” state. It is GRB (RGB type: V+ G R B) as the factory default.

RF remote button functions

1 color ring and 12 buttons in total, the function of buttons are shown as below:

Typical Applications 

About RF code.

The biggest advantage of this system is that it can not only solve the cabling problem in engineering wirelessly, but also realize a wired-like operation experience. In order to facilitate the early testing and debugging of the project, the factory status of the receiver is normally unpaired and each remote controller has a unique code value. The user should perform the matching work of the remote controller and the receiver during the installation of the project to avoid the mutual influence of the radio frequency remote control technology during the later use.

Please pay attention to the following 3 points before operation:

1) All equipment in the complete system after installation should have a unified and unique code value, so as to achieve the security and stability of the system.

2) The receiver can only store one code value and cannot be overwritten. Before learning the new code value, it is necessary to clear the original code of the receiver; the remote controller can only save one code value but can be overwritten and can also restore the factory settings. In order to facilitate the later maintenance, the three components that may be involved in the system (including receivers, handheld remote controllers, and panel remote controllers) can realize mutual learning of code values.

3) Since the receiver performs code value learning in the power-on state, batch-operation is available (power-one the all receivers which will be in same zone, and operate the matching/clearing the RF code all of them at the same time). And in order to avoid confusion in the area, it is recommended that each area has an independent power switch so that the power of other areas can be easily cut off when the code is being operated.

(1)Code pairing operation: means that the receiver will only be controlled by the value code remote control.

(2)Code clearing operation: means that the original code value of the receiver will be cleared and returned to the factory state. Then it can’t be controlled by any remote control, and can learn to a new code.

(3)Code learning operation between remote controls: Used to unify system code values or copy a new remote controls.

Since each remote control has its own unique code at the time of delivery, when there are multiple remote controls in one system, one of them (for example, remote control A) must be selected as the system code value, and the code value of the rest remote controls (for example, remote control B) should be copied to the same one.

About installation of remote control’s bracket:

1.Accessories include: bracket 1pc, 3M foam sponge glue 1pc, screw 2pcs, expansion tube 2pc.

2. There are 2 options for bracket installation:

1) Using screw and expansion tube make drilling installation (suitable for uneven and ash surface);

2) Using 3M foam sponge glue make free drilling installation (suitable for flat no ash surface).

Product information for placing order