Share
Brand： |
none |
Address： |
China |
Min.Order： |
none |
Supply： |
none |
Valid until： |
Long Term |
Type： |
Array |
Product Details
Airport/Heliport/Helipad/Helideck Revolving Rotating Beacon Warning Lights
Hunan Chendong Technology Co.,LTD (shorted as CDT)is a professional manufacturer for Green navigational aids products, mainly for aviation obstruction lights, helipad lightings and meteorological target lamp in China . CDT got ISO 9001:2008 certification the first year when established.As pioneer in China, our products are approved by ICAO and CAAC certificate. CDT keep acting as a solution provider for customers with specialty. And our products have been exported over 50 countries and areas all over the world.
- Product Picture
- Using Range of Rotating Beacon
This handbook describes apron rotation beacons manufactured to FAA AC 150 / 5345-12 and ICAO Annex 14 and Airport Design Manual. Pleasestrictly follow the FAA and ICAO and other relevant provisions of the norms of the use of the lamp.
- Technical Characteristics
| Interval | Parameter | Action |
| Every day | Lamp failure | Change Lamp |
| Light output is low | 1.If the glass surface is dirty, wipeit clean 2.Check lamp deviation or moisture 3.Check lamp aging or shifting | |
| Every Week | Light output channel obstructions | Clean the path and prism surface |
| Every Month | The presence of moisture and water(Visual inspection of prism inner surface) | 1. Turn on the lamp body 2. Clean, dry and check 3. Replace O-rings and other damaged parts |
| Every Two Month | Tighten the screw | Check the lamp body tightness bolts are locked |
| After 1200 hours 6.6A operation | Change Lamp Bulbs | Recommended When the service life is reached, replace the lamp systematically. At rated power (6.6A), up to 1200 hours. But in actual operation, the lamp life may reach 2000 to 4000 hours |
It is recommended to increase the number of maintenance during the rainy season to
ensure the normal operation of the lamp
It is suggested that the system replace the lamp when the lamp reaches the service life
(80% light intensity)
- Specification
- Light intensity, light color meet the requirements.
- Sophisticated optical control, light utilization, high brightness, outstanding optical
performance. - Lamps shape is handsome, good thermal performance, well-designed.
- The lamp uses a split structure, reducing impurities and moisture into the lamp,
improving the service life of lamp optics, reducing the number of maintenance operations. - The main body of the lamp is made of aluminum alloy, the fastener is made of stainless
steel, and the anti-corrosion performance is good. - Adopts high-precision machine tool processing, ensuring a full range of lamps quality and
accuracy.
- Adjust the Angle of the Lamp
Check the lamp pointer engraved clearly visible, loosen the side of the set screw, adjust the lamp elevation angle through the front and rear angle adjustment screw until the pointer points to a predetermined angle value, locking the set screw.
- Lamp Maintenance
The routine maintenance recommendations provided in this section are for informational purposes only. The airport may establish its own routine maintenance guidelines based on other regulations or the maintenance experience of the airport staff themselves.
Airport lighting maintenance, please refer to "1.0 Foreword" described, by professionals.
- Change Bulbs
Turn off the power, open the lamp cover, unplug the lamp pin. Holding the thumb and forefinger on the tail of the bulb, rotate the bulb to align the circular notch in the lower part of the lamp tray with the clip of the lamp holder and remove the bulb backward. Thumb and forefinger holding the tail of the bulb, the lower circular notch of the lamp tray alignment a snap bracket , rotate the bulb 90 degrees, so that the lamp bracket buckle stuck lamp panel, the lamp pin into the holder.
can be.
1. Never replace the lamp from the front of the lamp; remove the lamp.
2. The working position of the bulb is the direction of the notch of the .
| Application Environment | Technical Indicators |
| Altitude below 2500 meters; Outdoor: -40 ℃ - +55 ℃; Relative humidity: 95%; (+ 24.5 ℃), the maximum humidity can be greater than 100% ; Rain, snow, ice, water; Corrosive salt spray. | Halogen lamp3*150W; Lamp Using Life: ≥1000 hours; White,Green,Yellow Color; Lamp angle can be adjusted; 12 RPM, 36 times per minute flash; 304 Steel cabinet with powder layer; Voltage:AC220V. |
- Installlation Way
- If installed on a flat surface (such as concrete floor), the bafflewith expansion screws on the concrete floor.
- If installed in uneven ground (such as land) in this case,you need to be fixed in the concrete block.
- Installation Steps
- When open the package, check that the parts are complete and handle lamps carefully to avoid damage.
- Fix the lamp through the bottom plate screw and open the cover to connect the cable.
Q1. Can I have a sample order for Obstruction light?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.
Q2. What about the lead time?
A: Sample needs 3-5 days, mass production time needs 1-2 weeks for order quantity more than.
Q3. Do you have any MOQ limit for Obstruction light order?
A: Low MOQ, 1pc for sample checking is available.
Q4. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping also optional.
Q5. How to proceed an order for Obstruction light?
A: Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our suggestions.
Thirdly customer confirms the samples and places deposit for formal order.
Fourthly We arrange the production.
Q6. Is it OK to print my logo on Obstruction light product?
A: Yes. Please inform us formally before our production and confirm the design firstly based on our sample.
Q7: Do you offer guarantee for the products?
A: Yes, we offer 2-5 years warranty to our products.
Q8: How to deal with the faulty?
A: Firstly, Our products are produced in strict quality control system and the defective rate will be less than 0.2%.
Secondly, during the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.
Customer Reviews total 0 items