Typical Applications:

• Portable (flashlight, bicycle)

• Uplighters/Downlighters

• Decorative/Entertainment (stage light)

• Bollards/Security/Garden

• Indoor/Outdoor Commercial and Residential Architectural

Bridgelux 45mil Chips RGBWA UV LED Par Component LED Excellent LED Chip 18W RGBWA UV 6in1

Features:

• Well-known chip material, EPILEDS

• 99.99% gold wire bonding

• Full color spot, well color consistency

• Red-Green-Blue-White-Amber-UV 6 colors in one Package

• High flux per LED

• Low-temp & lead free reflow soldering

• More energy efficient than incandescent and most halogen lamps

• Low Voltage DC operated

• Instant light(less than 100ns)

Emitter Mechanical Dimensions

Notes:

1. The Cathode side of the emitter is denoted by "-" Sign in the lead frame.

2. Electrical insulation between the case and the board is required. Do not electrically connect either the anode or cathode to the slug.

3. Drawing not to scale.

4. All dimensions are in millimeters.

5. Unless otherwise indicated, tolerances are ± 0.2mm.

6. Please do not bend the leads of the LED, otherwise it will damage the LED.

7. Please do not use a force impact or pressure on the lens of the LED, otherwise it will cause a catastrophic failure.

Flux Characteristics at 700mA, Temperature=25℃

• LEDGUHON maintains a tolerance of ±5% on flux measurements.

• Please do not drive at rated current more than 1 second without proper heat sink.

Optical Characteristics at 700mA, Temperature=25℃

• LEDGUHON maintains a tolerance of ±1nm for dominant wavelength measurements.

Electrical Characteristics at 700mA, Temperature=25℃

• LEDGUHON maintains a tolerance of ±0.1v for voltage measurements

Absolute Maximum Rating

Red-Green-Blue-White-Amber-UV Spectrum, Temperature=25℃

Forward Current Characteristics, Temperature=25℃

1. Forward Voltage vs Forward Current

2. Forward Current vs Normalized Relative Luminous Flux

Soldering Conditions

• When soldering High Power Led, Heat may affect the electrical and optical characteristics of the LEDs.

• In soldering, do not stress the lead frame and the resin part under the high temperature.

• The silicone part should be protected from mechanical stress or vibration until the High Power Led return to room temperature after soldering.

• Preliminary heating to be at 140˜160℃ max, for 120 seconds max.

• Soldering heat to be at 260℃ max, for 3 seconds max.

• For manual soldering is not more than 3 seconds at max 260℃, under soldering iron.

Storage

• Before opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

• The LEDs should be used within one year.

• After opening the package, the LEDs should be kept at 30℃ or less and 30%RH or less.

• The LEDs should be used within one month after opening the package.

• If the moisture absorbent material(silicone) has fade away or the LED have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: 60℃±5℃ for 48 hours.

Handing LED

LEDGUHON recommends the following at all times when handing  LEDs or assemblies containing the these LEDs:

• When handing the LED with tools like Tweezer or Nipper, do not apply Mechanical Forces directly on LED's Surface.

• Do not touch with hand LED Lens surface directly. It may contaminate the Lens surface and affect on optical characteristics.

• LED should be handled from side because LED's molding material may be damaged with scratching on surface, piercing molding material and broking wire.

Attention: Electric Static Discharge (ESD) Protection

The symbol shown above herein to introduce "Electro-Optical-Characteristics". ESD protection has to considered and taken in the initial design stage. If manual work is needed, please ensure the device is well protective from ESD during all the process.

Option 1 - Tube Packing

Notes:

1. Drawing not to scale.

2. All dimensions are in millimeters.

3. Unless otherwise indicated, tolerances are ±0.2mm.

• Please do not open the moisture barrier bag(MBB) more than one week. This may cause the leads of LED discoloration. We recommend storing LEDGUHON's LEDs in a dry box after opening the MBB. The recommended storage conditions are temperature 5-30℃ and humidity less than 40% RH.

 1. Is there any discount for bulk order?

Yes, if you need bulk order or you want customized products, we can provide wholesale price.

2. How to place an order?

If you want to place an order, Please feel free to send us an inquiry email, we will reply you within 24 hours (working day).

3. What payment terms are available?

T/T, Western Union and PayPal are preferred.

4. Do you support drop shipping and how much is the shippping cost?

Yes, we support drop shipping. You should leave the receiver's information when you place the order, then we will send the goods according the address you have left. The shipping cost are based on your order's volume and weight, and it can be calculated.

5. All the pictures are real photo?

Yes, the pictures of all products on this page are 100% real shoot by us.

6. How about the quality of 18W RGBWA UV 6in1?

Please do not worry about the quality. Our company is the main manufacturer of 18W RGBWA UV 6in1 in China. Our products have exported worldwide since the year 2009.

7. Is there any custom duty and import tax?

Due to different policy in different countries, there might be some custom duty and import tax, but it is not considered in the price and should be paid by yourself. We are not responsible for any custom duty and import tax.

If you need more type of other High Power LED, Please find it on our website:

http://ledguhon.en.alibaba.com/productlist.html