Share
Brand： |
none |
Address： |
China |
Min.Order： |
none |
Supply： |
none |
Valid until： |
Long Term |
Product Details
- Combined LED driver & Emergency conversion module with LED panel light.
- Input voltage: 100-277V/50-60Hz
- Power factor: >0.9
- Output voltage: 26-42VDC
- Output power: 40W, 50W max.
- Constant current: 1000mA or 1200mA (wave code selection)
- Low ripple and noisy, flicker free
- Dimming range: 0-10V/10V PWM, 5%--100%
- Located in LVLE circuit
- Output short circuit and open circuit protection
- Built MCU controls the whole circuit
- ta: 10......50℃
- Battery pack:
IFR18650MUB 3.2V 1500mAH battery cells, 2S2P 6.4V 3000mAH 19.2WH.
Charge time: ≥24 hours
Battery pack protection: OSP, ODP, SCP, OTP
Datasheet
| Model | Item | YH07-5008WL (50W) | YH07-5008WL (40W) |
| Driver input | Rated input voltage | 100-277VAC | 100-277VAC |
| Frequency | 50-60Hz | 50-60Hz | |
| Input current | 0.7A max (100VAC) | 0.7A max (100VAC) | |
| Power factor | >0.9 | >0.9 | |
| Driver output | Output power | 50W max | 40W max |
| Output voltage | 26-42VDC (50VDC max) | 26-42VDC (50VDC max) | |
| Output current | 1200mA ±5% | 1000mA ± 5% | |
| Dimming range | 0...10VDC 5%...100% | 0...10VDC 5%...100% | |
Emergency driver input (charge) | Rated input voltage | 100-277VAC | 100-277VAC |
| Frequency | 50-60Hz | 50-60Hz | |
| Input current | 80mA max (100VAC) | 80mA max (100VAC) | |
| Power factor | >0.6 | >0.6 | |
| Input power | 4W max | 4W max | |
| Emergency driver output (discharge) | Output voltage | 26-42VDC (55VDC max) | 26-42VDC (55VDC max) |
| Output power | 8W (7...8.5W) | 8W (7...8.5W) | |
| Output current | 300mA max | 300mA max | |
| Battery backup | Battery pack | LiFePO4 6.4V 3.0AH (2S2P) | LiFePO4 6.4V 3.0AH (2S2P) |
| Charge time | >24 hours | >24 hours | |
| Duration time | >1.5 hours | >1.5 hours |
LED indicator
- The automatic test function is controlled by internal single chip microcomputer.
- Depending on the luminescent color of the LED indicator.
- It displays the working state and determines whether there is an exception.
- Red stable: charging mode
Red flashing: failure as below
Battery is not connected
Battery is defective
Load failure during emergency mode, open circuit/ short circuit.
Green stable: battery fully charged.
Red and Green off: discharging mode or mains supply disconnected.
Test switch
- Under normal working condition, the lamp will enter the discharge state by pressing the test switch.
- Release the switch and automatically return to the charging state.
- In the discharge mode, the discharge will be switched off according to the test switch for more than 3 seconds.
- Installed on the back of the panel requires safety and fixation.
- Only professional people (e.g. electrical engineer) can wire it.
- Please confirm that the electrical paramters of this product match with the luminaire.
- Please check the wiring method carefully before installation.
- Please power off mains supply before installation, and confirm the wiring is correct, then connect the battery, the last step is to turn on mains supply.
- To guarantee the rated discharge time, please charge the battery for more than 24 hours.
Please ensure that the voltage is 80% higher than the rated voltage, less than 110% of the highest rated voltage.
- Charge and discharge cycle needs to be done at least once every three months, and the continuous charging time can not exceed 3 months.
- Warranty
Warranty: 3 years
Except for the following circumstances
1) Improper installation or operation.
2) Misuse
3) Abuse
4) Unauthoruzed or improper repair alteration.
5) Accident or negligence in use, storage, transportation.
6) Any natural acts.
Customer Reviews total 0 items