Newest!! DC 5-24V DropLux Led controller D4 RGB/RGBW 2 in 1 LED controller with RF 24 key remote control

Product Features:

l  This product is a constant voltage controller, the standard product power supply voltage 5-24V is a wide voltage, and the power supply in this range can be used universally;

l  The output is 4 channels, the maximum current of each channel is 4A;

l  With power-off memory storage function;

l  Adopts RF 24-key wireless remote control, the maximum distance can reach 20 meters;

l  Adopts color balance key to achieve 1024 colors and can be saved as DIY modes;

l  Both remote control and receiver are 2 in 1 for RGB and RGBW, one product for 2 types of LED strips;

l  Short circuit protection function;

l  Output current: 3chs * 5A (RGB), 4chs * 4A (RGBW);

l  3-year warranty.

Technical Parameters

Dimensions

Interface Specifications

Direction for use

l  Connect the load wires at first, followed by the power wires.

l  Use the SET button to set the output type to be consistent with the type of LEDs connected to the load. The indicator flashes slowly: RGB, flashes quickly: RGBW.

Key functions for RGB

Key functions for RGBW

RF CODE

Receiver can be controlled by any one the same remote as factory default; remote control delivered with unique RF code as factory default; if unique-control is needed, please matching the code before installation and using.

Matching code operation

Receiver and Remote Control are coded as default, matching them before using, if unique-control or new-coded-remote is needed, pairing the remote and the receiver as below operation instructions before using:

Method 1:

1.Step 1: Pressing key “FLASH” and hold on, power on the controller, the load LEDs will be 50% brightness white as responding.

2.Step 2: Pressing “FLASH” 3times in 3 seconds, corresponding to the operation, the LED’s brightness will change as 25%-10%-back to preset level.

3.Code learning successfully, the receiver only can be controlled by the remote.

4.If not, please re-operate from step 1 to 2.

Method 2:

1.Step 1: Power on the controller after well connection.

2.Step 2: 5 seconds long pressing of the “SET” button (on receiver) until the indicator light lights up, pressing “FLASH” (on remote control) 1 time to finish ( “SET” button should be pressed also at the meanwhile), will see the load LEDs flash 3 times by successful operation.

3.Code learning successfully, the receiver only can be controlled by the remote.

4.If not, please re-operate from step 1 to 2.

Clear code operation

Back to factory default, wall-panel can be controlled by any one the same remote control.

Method 1:

1.Step 1: Pressing key “SMOOTH” and hold on, power on the controller, the load LEDs will be 50%  brightness white as responding.

2.Step 2: Pressing “SMOOTH” 3times in 3 seconds ,corresponding to the operation, the LED’s brightness will change as 25%-10%-back to preset level.

3.Code clearing successfully, the LEDs will be back to the status before the power off, and the receiver can be controlled by any remote control.

4.If not, please re-operate from step 1 to 2.

Method 2:

1.Step 1: Power on the controller after well connection.

2.Step 2: 5 seconds long pressing of the “SET” button (on receiver) until the indicator light lights up, pressing “SMOOTH” (on remote control) 1 time to finish ( “SET” button should be pressed also at the meanwhile), will see the load LEDs flash 3 times by successful operation.

3.Code learning successfully, the receiver only can be controlled by the remote.

4.If not, please re-operate from step 1 to 2.

Typical Applications

Application Circuit 1: RGB

Application Circuit 2: RGBW

Product information for placing order