Share
Brand： |
none |
Address： |
China |
Min.Order： |
none |
Supply： |
none |
Valid until： |
Long Term |
Product Details
1. Module introduction
Multi-functional time relay module, various working voltages are optional, DC5V 12V 24V, the output end is isolated from the circuit by relay, which can control low-voltage appliances, 220V circuit and up to 10A control ability.Up to 27 operating modes, meet various test and automatic control applications, delay time is adjustable from 0.01 seconds to 999 minutes.The trigger port can be triggered by a voltage signal or by a key.
| Supply voltage | DC 5V 12V 24V optional |
Trigger terminal voltage | DC 3~30V | |
Maximum control current of relay | 10A | |
Module size | 63*42*20mm(length, width and height) |
1. Module Instructions
Setting of working parameters: hold down the button S1, and the display screen will display p-xx after 0.5 seconds. Press S2 and S3 to change the working mode.After selecting the working mode, press S1 to enter the setting of time A, and the screen displays Axxx. At this time, press S2 and S3 to modify time parameters of A; press S2 and S3 to add or subtract 1, long press fast add or subtract 10, and press S4 to set the position of the decimal point.After setting A time, press S1 to set B time, and the screen displays BXXX. At this time, press S2 and S3 to modify B time parameters.After setting B time, press S1 for the last time to exit the setting state and save all parameters.
Meaning of decimal position:
Ax. Xx decimal point in the hundreds place, time range 0.01~9.99 seconds
Axx.x decimal point in the tens place, time range 0.1~99.9 seconds
Axxx. Decimal in the ones place, time range 1~999 seconds
Axxx has no decimal point and a time range of 1 to 999 minutes
Close the display screen: press S4 to close the display screen when not set, and then open it again.
| P-01: | The relay is disconnected after power supply or trigger, and the relay is closed after delay A time |
| P-02: | After power on or trigger, the relay is disconnected after delay A time |
| P-03: | Inching mode, signal absorption, no signal off |
| P-04: | In self-locking mode, the relay state is flipped once after each trigger |
| P-05: | After the trigger, the relay will close and stop after the delay of A time. The trigger cannot be repeated during the delay |
| P-06: | When triggered, the relay will close and stop after delay A time. When triggered repeatedly during delay, the timing will be restarted |
| P-07: | After triggering, the relay will close, stop after delay A second, repeat triggering during delay, and the time will accumulate |
| P-08: | When triggered, the relay will close and stop after delay of A second. If triggered again during delay, it will stop immediately |
| P-09: | After the trigger, the relay pulls in, and the delay of A second stops after the signal disappears, and the trigger starts again during the delay |
| P-10: | After power on, the absorption time A, the disconnect time B, infinite cycle |
| P-11: | When there is A continuous signal, the time of absorption A, the time of disconnection B, the infinite cycle, the signal disappears immediately stop |
| P-12: | Trigger A time to close, disconnect B time, infinite loop, trigger again to stop |
| P-13: | The on-power relay is closed, the relay is disconnected after triggering, and the relay is closed after delay A time |
| P-14: | There is A continuous signal. When the time exceeds A, the relay closes and the signal disappears. The relay disconnects |
| P-15: | The continuous signal relay is disconnected, and the relay closes after the signal disappears for more than A time |
| P-16: | When the continuous signal exceeds A time, the relay closes, and when the signal disappears beyond A time, the relay disconnects |
| P-17: | After A continuous signal exceeds A time, the relay is closed. After the signal disappears, the relay is disconnected again after A continuous signal exceeds A time |
| P-18: | Trigger. After A time, the relay is closed and triggered again. After A time, the relay is disconnected |
| P-19: | The relay with continuous signal catches A time and then stops, and then stops if the signal disappears and the relay catches A time again |
| P-20: | With impulse signal (rising or falling edge), the relay stops. Without impulse signal, the relay absorbs after delay A time [continuous high level or continuous low level is considered as no pulse] |
| P-21: | After power supply, delay A time after relay closes, and stop after B time |
| P-22: | After triggering, delay A time after the relay closes, and stop after B time |
| P-23: | When there is A continuous signal and it exceeds the time of A, the relay will close and stop after the time of B |
| P-24: | After triggering, the relay stops after absorbing A time, and then timing B time, which cannot be triggered within A+B time |
| P-25: | After triggering, the relay stops after the time of absorbing A, timing the time of B, and then stops after the time of absorbing A, during which it cannot be repeatedly triggered |
| P-26: | Counting mode, rising edge trigger, every time the rising edge is detected, value +1, maximum count 9999, maximum frequency 20Hz, press S1 button to clear zero |
| P-27: | Counting mode, falling edge trigger, every time the falling edge is detected, value +1, maximum count 9999, maximum frequency 20Hz, press S1 button to clear zero |
We are professional electronic components supplier with 10 year experience. We can provide One-Stop BOM quotation for you. BOM include: IC Chips,Transistor, IGBT Module, Sensor, Lense, VCM Holder, IR filter, SMD inductance, Resistors, Capacitors, Tantalum capacitors, Magnetic beads, Connectors, Filters, Electrolytic capacitors, Diodes, Relay,Cooling fans etc products.
Because of we have stock many kinds of electronic components, so can not upload one by one, if you can"t find what you need in our store, please contact us, we will offer in the first time. Thank you in advance.
Packaging & Delivery & How to order | |
| Stock | More than 50 million USD stock for more than 50000 models. Almost all of the orders can be shipped in three days. |
| Quality Control | Each of the products will be checked by QC group before shipment. |
| Packing | Original Standard Official Factory Encapsulation Technology Packing + Standard Export Package |
| Shipping | Shipping by DHL, FEDEX, UPS, TNT, China Post etc. |
| Payment | We can accept T/T,E-checking, Western ,Paypal etc. also follow customers" requests |
Customer Reviews total 0 items